Welcome Inspire Pilots!
Join our free DJI Inspire community today!
Sign up

Recent content by dronie

  1. dronie

    Inspire 2 - Gimbal Noise During Calibration

    Gimbal Noise on latest fw. After updating my gimbal now makes a loud grinding noise when calibrating (both on 12 & 45 mm). After calibration the noise stop. Does anybody else get this? Is it ok for it to make this grinding noise it never did before - or know how to fix it? Thanks.
  2. dronie

    Inspire 2 firmware update - V01.0.0240

    Dated 2016.03.02. Let’s just hope the DJI engineers pay more attention to detail ;-)
  3. dronie

    Cinema DNG vs. Pro Res

    Other CON's to the ProRes format from my point of view: 10-bit vs. 12-bit CDNG (up to 3840x2160 at 50FPS (47.952fps), 4096x2160 at 50FPS (47.952fps), and 5280x2972 at 30FPS (29.97fps) Even ProRes 4444 seems to only be 10-bit so the only upside to using this vs. 422 is 4.4.4 chroma but at a the...
  4. dronie

    Loose motor - rattling sound - VIDEO

    Thanks again - I contacted DJI to get a replacement set as ver. 2 of the props have the foam inside.
  5. dronie

    Loose motor - rattling sound - VIDEO

    Thanks for the tip - a small piece of paper inside solved it.
  6. dronie

    Loose motor - rattling sound - VIDEO

    My front left motor sounds loose and makes a rattling sound when I spin the prop. It's also the only motor where the prop is loose. I've seen quite a lot of posts about issues with Inspire 2 props/motors now. Guess this qualifies for a replacement? Password: i2
  7. dronie

    Once again DJI announces a spec - and removes it

    Originally Inspire 2 was sold with the promise of a top speed around 96 kph. Shortly after they lowered the top speed. Todays update of the GO app 4 looks like it decreases the top speed to 72 km/pr hour (45 mph)! Just like they did with the I1.
  8. dronie

    Yaw camera (C1+LSW) stops working when landing gear goes up

    The problem is, that now it ONLY works in Free mode, whereas on the I1 it worked in Follow mode. I hope DJI will fix this soon and give us back the ability to yaw in Follow mode.
  9. dronie

    Yaw camera (C1+LSW) stops working when landing gear goes up

    Exactly. I've always flown in Flown Mode on I1 doing tilt/pans just switching btw them with C1. Now there's a lot of extra steps involved which potentially can ruin, or at the very least, make pans more difficult. With this way of doing it, you now need to move your hands of the sticks, press...
  10. dronie

    Yaw camera (C1+LSW) stops working when landing gear goes up

    Hi, I'm testing my new I2 + X5S these dasy and observed a strange behaviour. To Yaw the camera, you now need to press and hold C1 + turn Left Scroll Wheel (LSW). That works fine when I test it on the ground, when motors are running and during hover. But as soon as I raise the landing gear I...
  11. dronie

    Meta data on video files is dated in 1951

    Just unpacked my I2/X5S. The meta data on all video files (H.264 as I don't have the SSD yet), dates them with 1951. Photos are dated correctly. How can that be fixed?
  12. dronie

    First Impressions (not a review) > DJI GROUND STATION PRO app

    First Impressions (not a review) > DJI GROUND STATION PRO app So DJI released and updated GS Pro app which enables you to create WayPoint Routes (without flying them first), Virtual Fence and 3D Map Area. I have no practical use for "Virtual Fence" where you can setup an area in which the...
  13. dronie

    Comparison video X5 vs. X5R

    Maybe it looks sharper because the X5 footage was shot in NONE (0,0,0), but this tends to be over sharpened in camera. I would dial Sharpness down to -2 and add it in post.
  14. dronie

    Comparison video X5 vs. X5R

    ProRes X5R on the left - posted in the comments.