I used duracoat electric lime. I got the white but didn't use it.
Thanks Benji for taking time to offer a detailed
description of the body removal. Once again ..... that is one impressive Inspire.
I used goo be gone and let it dry, if you are using Plexi Dip and are putting the screws back in make sure to use some vegetable oil or it will grab and pull the paint off, it sucks because you will need to peel and repaint lolHi. I ordered a couple cans of orange blaze. Any special surface preparation to the shiny white plastic on the inspire? Or any other tips you might have to add for a successful application.
Thanks. Dennis
Thanks. I'm stil a little confused over the battery painting procedure. Did you spray over the clear plastic LED green lights rather than taping them off? And the lights are bright enough to illuminate through the layer of paint?I used goo be gone and let it dry, if you are using Plexi Dip and are putting the screws back in make sure to use some vegetable oil or it will grab and pull the paint off, it sucks because you will need to peel and repaint lol
It could be if you use a paint with any metal type properties in it, the paint we are using does not have that and should not be a problem.Hopefully GPS reception isn't affected
It could be if you use a paint with any metal type properties in it, the paint we are using does not have that and should not be a problem.
One more question about the bottom trim piece. You mentioned you used a heat gun to remove it. I see that the back of the trim piece has tabs on it. So is the function of the heat gun to make the piece more plyable and easy to pull off. And then how easy is it to put back on? ThanksDuracoat is a two part paint that cures hard. It's meant for firearms and adheres to metal and plastic. They do sell a version that comes with a compressed air can to apply it. I personally just used my airbrush.
As far as taking it apart I was able to do it without looking anything up online. I used a heat gun to remove the bottom trim piece. One note is the ribbon cables have a release clip unlike the phantom cables.
The bottom ultrasonic sensor/ camera should cable should be released from the frame not the sensor. It's easy enough to get the sensor off but near impossible to plug back in that way.
I went to home depot and bought a husky kit, like 9 bucksWhat size micro screwdriver is required to take off the screws on the rear light panel?
My custom paint job DJI Inspire 1 View attachment 1272 View attachment 1272 View attachment 1273 View attachment 1274 View attachment 1275
Hey any recommendations for fpv camera?vtx --> ImmersionRC 5.8GHz 600mw Audio / Video Transmitter
camera mount --> https://www.google.nl/search?q=tripod+magneet&espv=2&biw=1920&bih=935&tbm=isch&imgil=khK3_trfE1DtYM%3A%3BpeY4_U6wlbVHHM%3Bhttp%253A%252F%252Fwww.digitalefotografietips.nl%252Fapparatuur%252Fstatief%252F&source=iu&pf=m&fir=khK3_trfE1DtYM%3A%2CpeY4_U6wlbVHHM%2C_&usg=__2SZ10_dSoJHitGmzhB5yEPjcuvc=&ved=0CC4Qyjc&ei=MN8eVbjfNoPdaLaPgPgI#imgrc=khK3_trfE1DtYM%3A;peY4_U6wlbVHHM;http%3A%2F%2Fcdn.digitalefotografietips.nl%2Fwp-content%2Fuploads%2F2010%2F02%2Fgorillapodmagnetic.jpg;http%3A%2F%2Fwww.digitalefotografietips.nl%2Fapparatuur%2Fstatief%2F;500;466
batery --> 800mAh lipo
paint --> car paint ****
lol
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?