DJI CrystalSky Monitor Owner Discussion by Advexure

cvanhoose · Jul 3, 2017

Nothing but problems with the new monitors and the latest Inspire 2 firmware. Will not allow an altitude higher than 100ft.
Just canceled a flight due to the latest firmware.
There is no way to update the app in the monitor.
Does anyone no of a way or link to the software update?
Funny thing is I was able to test 4 flights after the updates with no issues.

inkytog · Jul 3, 2017

cvanhoose said:
Nothing but problems with the new monitors and the latest Inspire 2 firmware. Will not allow an altitude higher than 100ft.
Just canceled a flight due to the latest firmware.
There is no way to update the app in the monitor.
Does anyone no of a way or link to the software update?

To update the screen or the inspire? Does the CS not use the regular DJI go app?

cvanhoose · Jul 3, 2017

inkytog said:
To update the screen or the inspire? Does the CS not use the regular DJI go app?

There is no way to update the CS app

inkytog · Jul 3, 2017

cvanhoose said:
There is no way to update the CS app

Is there even an update available?

cvanhoose · Jul 3, 2017

inkytog said:
Is there even an update available?

Software notification says to update to match the latest firmware. Let’s hope so.

inkytog · Jul 3, 2017

Ah ok. I don't see one.

Tom Dillon · Jul 3, 2017

Same problem. Worked fine last week.

oblivie · Jul 3, 2017

Hey.... any of you guys happen to have the gpc landing mode case..... wondering where you put the cs monitor, seeing that it comes build to handle 2 iPads, which are almost half the thicknesses of the cs

Mark Taylor · Jul 3, 2017

cvanhoose said:
There is no way to update the CS app

Nothing shows up when you connect to DJI Assistant 2 via the micro-USB port and OTG cable?

cvanhoose · Jul 3, 2017

Mark Taylor said:
Nothing shows up when you connect to DJI Assistant 2 via the micro-USB port and OTG cable?

No. Can’t downgrade the aircraft either.

Florida Drone Supply · Jul 3, 2017

oblivie said:
Hey.... any of you guys happen to have the gpc landing mode case..... wondering where you put the cs monitor, seeing that it comes build to handle 2 iPads, which are almost half the thicknesses of the cs

We were just looking at that for a client. There are a couple choices based on which one you get. The 5.5 fits in one of the accessory spots and the larger one will fit in an iPad spot if you remove the foam that goes to the edge of the case - widening the cutout. Credit to @AeroMirage for that second idea.

oblivie · Jul 3, 2017

Florida Drone Supply said:
We were just looking at that for a client. There are a couple choices based on which one you get. The 5.5 fits in one of the accessory spots and the larger one will fit in an iPad spot if you remove the foam that goes to the edge of the case - widening the cutout. Credit to @AeroMirage for that second idea. View attachment 14609
View attachment 14610

Won't hit/ rub on the case?
Or is there a case for the cs?

Tom Dillon · Jul 3, 2017

cvanhoose said:
Nothing but problems with the new monitors and the latest Inspire 2 firmware. Will not allow an altitude higher than 100ft.
Just canceled a flight due to the latest firmware.
There is no way to update the app in the monitor.
Does anyone no of a way or link to the software update?
Funny thing is I was able to test 4 flights after the updates with no issues.

That time zone does your CS say you are in. Mine said China. I did a reset last week and I think I forgot to change the time zone.

cvanhoose · Jul 3, 2017

Tom Dillon said:
That time zone does your CS say you are in. Mine said China. I did a reset last week and I think I forgot to change the time zone.

It’s correct. I have it on auto. -4

Tom Dillon · Jul 3, 2017

OK. I have no idea what the hell is wrong. If you figure it out let me know.

Thanks

Tom Dillon · Jul 3, 2017

cvanhoose said:
It’s correct. I have it on auto. -4

If I boot everything up with the iPad plugged in and launch DJI Go then unplug my iPad and plug the CS in it works fine.

SanCap · Jul 3, 2017

Tom Dillon said:
If I boot everything up with the iPad plugged in and launch DJI Go then unplug my iPad and plug the CS in it works fine.

That worked for me also.

Florida Drone Supply · Jul 3, 2017

oblivie said:
Won't hit/ rub on the case?
Or is there a case for the cs?

No case for the CrystalSky, but the space is wide enough to add a thin protection layer or you could put the monitor in a bubble wrap pouch or any type of sleeve.

AeroMirage · Jul 3, 2017

oblivie said:
Won't hit/ rub on the case?

Already thought of that........

cvanhoose · Jul 3, 2017

Tom Dillon said:
OK. I have no idea what the hell is wrong. If you figure it out let me know.

Thanks

Hey Tom, I have a fix for now. The info is in this thread: CrystalSky not compatible - latest Inspire 2 firmware

CrystalSky not compatible - latest Inspire 2 firmware

DJI CrystalSky Monitor Owner Discussion by Advexure

Similar threads

Privacy & Transparency

Privacy & Transparency