No - there was a firmware bug in the battery algorithm which incorrectly calculated the depletion curve of the packs. This has now been addressed.
No - there was a firmware bug in the battery algorithm which incorrectly calculated the depletion curve of the packs. This has now been addressed.It looks like you people making problems themselves . Any Lipo manual says that LIPO batteries must be fully and FRESHLY charged before EACH flight. Keep it simple - just follow the rules.
Never had problems with the batteries on the Inspire, but got sh-d
my pants flying P3Pro on max height and received the warning message to lend immediately dew to low power in all batteries cells
That happened when I left fully charged batteries for the couple of days.
Now I charge them strictly in a day the flight.
I downloaded the latest firmware last night (1.5.0.30)and spent all last night and the best part of today trying to get it loaded. On inserting the disk and switching on the drone, I just got a steady flashing light rather than the usual beep sounds etc. I tried I don't know how many times formatting the disk and retrying only for the same issue to repeat. The camera screen still informed me of upgrade required. I finally managed to get it loaded, but with a message on the screen "reformatting is suggested" and also despite repeated calibrations, still have some of the readings way out and still requiring calibration. Anyone else have this issue and more importantly a fix? DJI are saying they are not aware of the issue, but I have seen some posts detailing the same issue.Release notes:
What’s New:
Notes:
- Fixed battery level fluctuation issue.
- The X3 gimbal on the Inspire 1 is now compatible with the Osmo.
- Follow Me feature now supported in Intelligent Flight Mode.
- Optimized HDR performance.
- Adjusted video storage rate to 60 Mbps at 1080p60, and 40 Mbps at 1080p30.
- Added a feature to smooth the pitch, roll and yaw movement of the X3 gimbal from the DJI GO app.
- Enforced read-only access for the data in the flight recorder.
- Optimized sampling methods for the Vision Position System to improve its stability.
http://dl.djicdn.com/downloads/inspire_1/en/Inspire_1_Release_Note_en_v1.5.0.30.pdf
- Hibernation and gimbal protection is not supported on the Inspire 1 X3 gimbal.
- Battery firmware is included in this All-in-One firmware update. Update all Intelligent Flight Batteries
by using this firmware.
- The firmware can only be downgraded to v1.4.10 or later.
- Calibrate the Inspire 1 X3 gimbal when using it on the Osmo for the first time.
I downloaded the latest firmware last night (1.5.0.30)and spent all last night and the best part of today trying to get it loaded. On inserting the disk and switching on the drone, I just got a steady flashing light rather than the usual beep sounds etc. I tried I don't know how many times formatting the disk and retrying only for the same issue to repeat. The camera screen still informed me of upgrade required. I finally managed to get it loaded, but with a message on the screen "reformatting is suggested" and also despite repeated calibrations, still have some of the readings way out and still requiring calibration. Anyone else have this issue and more importantly a fix? DJI are saying they are not aware of the issue, but I have seen some posts detailing the same issue.
Best if you also contact DJI as they are telling me they are not aware of the issue and I should return my drone for repair. Not confirmed that it would be repaired under warranty!! It's obviously a problem with the firmware.....I have had a similar problem. My Inspire will not update to 1.5 either, all I'm getting is that and update is required on my RC. I do the usual stuff to update and i get nothing, no beeping, nothing. I also would like to know if there is anyone with a solution.
IskyBest if you also contact DJI as they are telling me they are not aware of the issue and I should return my drone for repair. Not confirmed that it would be repaired under warranty!! It's obviously a problem with the firmware.....
Mr Editor, do you have any suggestions?No - there was a firmware bug in the battery algorithm which incorrectly calculated the depletion curve of the packs. This has now been addressed.
About what? - The battery voltage drop syndrome which has now been fixed?Mr Editor, do you have any suggestions?
Maybe this has been covered, I haven't read the entire thread, but mine won't take updates from the 64gb cards I normally fly with. I have to use the 4gb card that came with the inspire. I am pretty sure it has to do with the formatting limits that the firmware will accept.
Also, after each update, I deleted everything but the bin file for the subsequent updates, getting rid of the log files and folders that booting creates.
Does the f"ollow me" function work? I kept getting "gps signal to weak", but I could set my home point to the controller fine. I was also above the 10m height so am I missing something?
Wifi, I thought it used the gps from the controller?
Sent from my iPad using Tapatalk
You need to have cellular.
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?