New Firmware v1.3.0.00 Aug 4 2015

alan brooks · Aug 9, 2015

turn of the smart return to home this disables the low rth function

BOO · Aug 9, 2015

alan brooks said:
turn of the smart return to home this disables the low rth function

Where is dat option alan?
Thanks, i tried everything...no Result

IrishSights · Aug 9, 2015

Cheeky Monkey said:
Did you know there has been a shield recall, due to heat and fire concern?

Email from Amazon stated:
Hello,

We've recently learned of a potential safety issue concerning NVIDIA Shield 8 inch Full HD Gaming Tablet (NVIDIA Tegra K1, 2GB RAM, 16GB Storage, Wi-Fi, Bluetooth 4.0, Mini HDMI, Micro USB 2.0, MicroSD) which you bought in order # 026-3756625-1003536.

The manufacturer has announced a potential defect affecting the battery in these tablets which means that they can overheat and pose a fire hazard. Please stop using this item immediately and follow the guidance in the link below.

More details, including what you should do and where you can seek assistance, can be found in the following notification:

http://tabletrecall.expertproductinquiry.com/

UK customers can contact NVIDIA directly at: 0-808-189-3133.

If you're outside the UK and need to contact NVIDIA by phone you can find other numbers here:

http://tabletrecall.expertproductinquiry.com/faq

If you bought this item for someone else, please get in touch with them and pass on this information.

We're sorry for any inconvenience caused and hope to see you again soon.

Regards,

Customer Service Department
Amazon.co.uk

Please note: This e-mail was sent from a notification-only address that can't accept incoming e-mail. Please don't reply to this message.

Just a tad off topic there!

BOO · Aug 9, 2015

This is The printscreen

BOO · Aug 9, 2015

alan brooks said:
turn of the smart return to home this disables the low rth function

It was off..... ;(

Azsweetwater · Aug 9, 2015

========== 2014.01.01 00:00:04 remo-con disconnect======
Packet: WM610_FW_V01.03.00.00.bin
Upgrading ...
Result: Success.
Uh I think that says you upgraded successfully.

On a side note I just updated my I1 controller and 2 batteries without issue. Flew one battery down to 5% and letting it cool before charging it, getting ready to fly the second bat down and do the same thing, I didn't have any issues with the AC, didn't watch the video screen much but when I did it seemed to show minimal lag, I fly mostly in atti mode and only switch to gps mode when I get to where I want to be for the video, I stay in gps mode when I am near and am ready to switch to atti mode at the first sign of trouble. I also fly a F550 with NAZA v2 gps as well as 2 QAV250 class racers. I am a firm believer in being able to control my craft by myself before I let the computer take it over, at least I know I should be able to recover from most problems.

Dave Crago · Aug 9, 2015

Updated FW on A/C, RC and 4 batteries without problems. Calibrated IMU and Compass and then flew the first 2 batteries down to 10%, kept A/C on and let batteries drop to below 5% with fan blowing on them. All went well, flew both flights in ATTI mode for the first time, which gave me more confidence in the Inspire and my control of it. Will fly the last 2 batteries later.

Ray787 · Aug 9, 2015

Figbar said:
I just downloaded the firmware and updated my Inspire...no problems...got a text readout that said "succesfull."

I am having issue upgrading the RC.

I am using an IPad Air and updated the DJI Pilot App which now is a DJI GO APP.

Reading the firmare update instructions for the RC...it says to do this upgrade throught the APP.

When I fire everything up:

The APP does indicate that the RC firmware needs to be upgraded on the initial overall status screen...but then I get a message that says, "The RC soesn't support upgrading firmware through the APP, please upgrade with a USB Disk."

So I connect the USB disk with the firmware upgrade at the root level (as I have always updated the RC in the past) to the RC...and nothing happens.

I know the cable and USB reader /card are good...they read on my computer.

Does anyone have any suggestions?

Thanks

Hello Figbar .... I had the EXACT same problem.... Everything went perfect until I tried to update the transmitter with the new 2015-08-04.... Did you find any solutions

Cheeky Monkey · Aug 9, 2015

Ray787 said:
Hello Figbar .... I had the EXACT same problem.... Everything went perfect until I tried to update the transmitter with the new 2015-08-04.... Did you find any solutions

Hi Ray787 & Figbar,

I had same problem I eventually tried a std alone usb stick rather than micro Sd in a usb reader and it worked fine, you may have to try several usb sticks and make sure they are formatted correctly

Regards
Chris

Cheeky Monkey · Aug 9, 2015

IrishSights said:
Just a tad off topic there!

Yeah, not sure what happened there, must have clicked back a page then wrong link as was replying to a thread where guy that mentioned his Nvidia shield overheating, thanks for noticing though!

Blue Bird · Aug 9, 2015

The USB stick would not work for me when it came to updating RC. I used The USB cord to gimbal method for updating the RC. It worked like a charm for all of my I1's and Phantom 3's A nd P.

Kirk Voclain · Aug 9, 2015

I upgraded over the weekend....all I did was follow the instructions provided by DJI, "TO THE LETTER".....and I had zero problems!!!!

I read the instructions 3 times before I began the upgrade.....flew all 5 batteries down to 2%....recharged....and frankly......everything seems to be EXACTLY like it was before!

WELL????? Except for the fact that I can flip my switch 4 times....kill the camera and gimbal....then remove it....and it kicks into travel mode.....NICE FEATURE!!! Thanks!

Kirk

Alastair · Aug 9, 2015

Huh??? Didn't know abou t that one!

rbrdly · Aug 9, 2015

Don't know why you would.
They only put it in the instructions and firmware release notes.

rbrdly · Aug 9, 2015

Azsweetwater said:
Uh I think that says you upgraded successfully.

Uh, I think it also says it failed 4 times after that ONE that you singled out.

As far as I can tell, a single controller I1 setup updates:
AC
ESC
Camera
Gimbal (Does it do this separately to the camera?)
Battery (seems to store/report multiple entries - confusing)
Controller

Seeing one success means nothing (aside from one thing being updated successfully).

It would be nice if their logs told you more clearly which component the entry was referring to.

Alastair · Aug 9, 2015

Your sarcasm is uncalled for.

rbrdly · Aug 9, 2015

You’re absolutely right.

Alastair · Aug 9, 2015

And you were right too, I didn't read the release notes. I would have normally, however, the app auto update was on on my iPad and it automatically updated to the dji go app. I felt I had no choice but to update the AC. I then had an issue with it not going travel mode and became consumed with others having the same problem. I totally forgot about the release notes and was surprised to see the post here.....Safe flying!

Rowdy · Aug 10, 2015

Help please. Downloading the Zip file V1.3 to a PC is fine. What program is required on the PC or what format to load the Bin file onto the SD card. My PC defaults to VLC media player which I believe is no good. What format do I need the bin file in and how do I achieve that? thank you.

Alastair · Aug 10, 2015

You need either Winrar or I believe win zip to decompress file. There should be three files, one of which will be the bin file.

New Firmware v1.3.0.00 Aug 4 2015

alan brooks

BOO

IrishSights

BOO

Attachments

BOO

Azsweetwater

Dave Crago

Ray787

Cheeky Monkey

Cheeky Monkey

Blue Bird

Kirk Voclain

Alastair

rbrdly

rbrdly

Alastair

rbrdly

Alastair

Rowdy

Alastair

Similar threads

New Firmware v1.3.0.00 Aug 4 2015

Attachments

Similar threads

Privacy & Transparency

Privacy & Transparency