Firmware Update v1.2.0.17 Available

[Kilrah]

You may need to rebind (I didn't), but most importantly you NEED to update the radio as well before you can reconnect to the aircraft.
Both stated in the firmware upgrade manual.

 

[InspiredOne]

OK, now I'm totally lost. How do I upgrade the radio?

 

[Kilrah]

How to Update Firmware

Is it really that hard to look at the manual linked right below the firmware file download?

 

[GizaDog]

OK, now I'm totally lost. How do I upgrade the radio?

Plug RC in to Camera on Inspire. Start RC and let run till the blue light turns green. Its all in the "How to Firmware" PDF.

 

[InspiredOne]

How to Update Firmware

Is it really that hard to look at the manual linked right below the firmware file download?

I can do without the attitude, right now.

 

[RJ Evans]

Thanks, RJ.

I don't care what the other members say, I think you're all right!

Didn't know I was in the dog house. You're welcome.

 

[The Editor]

This is not the version that we have been test for the last two weeks. In fact we are waiting for a revision on that right now. As far as I know this was a minor housekeep update.

Thanks for the reply Ed - In that case I will wait until the next update as currently I have zero problems.

 

[RJ Evans]

OK, now I'm totally lost. How do I upgrade the radio?

Turn off the RC TX. Put the update file on a USB drive, plug it into the USB on the back of the RC TX. Turn on the RC TX. It will update from there. When it's done, you'll see a green light.

 

[The Editor]

Here is what mine is doing after a "status: canceled" on the Inspire. I was able to update the remote control successfully.

EDIT: This happens to be an issue with the RC being to close to the Inspire.

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

Why do you have two batteries numbered Number 4?.... Doesn't that get confusing?

 

[InspiredOne]

Turn off the RC TX. Put the update file on a USB drive, plug it into the USB on the back of the RC TX. Turn on the RC TX. It will update from there. When it's done, you'll see a green light.

Thanks, RJ, for your patience. I did all that, got the green light, but they still aren't talking to one another. Can't figure out what I've done wrong.

 

[ThePagerGeek]

So, I have a dual controller setup.
Remote Controller 1 upgraded ok.
Remote Controller 2 was upgrading ok, but then got stuck with blue flashing and I hard reset it. Now it turns on with a solid white status light. My suspicion is the firmware didn't completely load.

I have tried to erase and reload the firmware on the SD, then start the process again, but it doesn't begin it's upgrade process. Just a solid white light.

Is there a way to force the controller into a bootloader or force load mode?

 

[RJ Evans]

Thanks, RJ, for your patience. I did all that, got the green light, but they still aren't talking to one another. Can't figure out what I've done wrong.

Turn them both off. Then turn on the RC TX, then the AC.

 

[InspiredOne]

Turn them both off. Then turn on the RC TX, then the AC.

Yep, I did that already--no go.

 

[RJ Evans]

Yep, I did that already--no go.

In that case you'll have to rebind the RC TX to the AC. Instructions are in the manual. Pretty easy. You'll get it.

 

[GizaDog]

Not at all. BAT4 are the TB47 and BATFOUR is the TB48

 

[InspiredOne]

Thanks, RJ!

 

[RJ Evans]

Thanks, RJ!

You're more than welcome.

 

[Deleted member 18003]

I have already updated my inspire and controller. I just received a new battery in the mail. Does the battery also need a firmware update?

 

[RJ Evans]

I have already updated my inspire and controller. I just received a new battery in the mail. Does the battery also need a firmware update?

The app would indicate that, if it were needed. As far as I know (following my update), it is not needed.

 

[InspiredOne]

"Re-linking" did not work.