Upon start up of the AC, it immediately starts beeping. It wont allow me to do any form of calibration, and the update wont take. I've written DJI LA, and I'll contact the dealer I purchased it from first thing in the morning.
Firmware v1.4.0.10 - 7th Sept 2015 Released
- Thread starter dronie
- Start date
- Joined
- Mar 29, 2015
- Messages
- 1,257
- Reaction score
- 590
- Location
- Buckie, Scotland, UK
- Website
- www.moraysky.co.uk
The date always shows 1-1-2014. This is the clock start date that is not updated until the aircraft receives a GPS update. Ignore it.
- Joined
- Mar 29, 2015
- Messages
- 1,257
- Reaction score
- 590
- Location
- Buckie, Scotland, UK
- Website
- www.moraysky.co.uk
IMPORTANT NOTICE
DJI has placed a banner on their Download page advising users to ensure that they upgrade to FW 1.3.0.0 before installing FW 1.4.0.10. This is to make sure that the RC is correctly upgraded without complications.
DJI has placed a banner on their Download page advising users to ensure that they upgrade to FW 1.3.0.0 before installing FW 1.4.0.10. This is to make sure that the RC is correctly upgraded without complications.
So, members on Firmware v1.2.1.06 or older must first update the RC with Firmware v1.3.0.00 and then update the Inspire 1 and batteries with Firmware v1.4.0.10.
Can the RC be updated with a USB stick as before or is it updated via the latest Go App?
Dji tech support have mysteriously disappeared...
- Joined
- Mar 29, 2015
- Messages
- 1,257
- Reaction score
- 590
- Location
- Buckie, Scotland, UK
- Website
- www.moraysky.co.uk
I cannot recall preciously. At one point I had to use the USB cable connected to the camera gimbal to update my RC. Alternatively, if you are having problems updating your RC to FW 1.3.0.0 try this Inspire 1 RC not updating - Instructions on how to reset RC | DJI Inspire Forum
sounds to me dji has no faith in the inspire. and are pushing everything towards phantom phasing out the inspire.
All done.
Updated ios Dji Go App to latest version.
RC updated to 1.3 via micro USB card reader.
Updated bird to 1.3 then 1.4 even tho 1.3 could have been skipped.
Updated all 150 batteries to 1.4
Completed IMU calibration.
Completed camera calibration.
Completed stick calibration.
Completed compass calibration outside.
Now just gotta complete battery calibration.
Thanks gentlemen.
Updated ios Dji Go App to latest version.
RC updated to 1.3 via micro USB card reader.
Updated bird to 1.3 then 1.4 even tho 1.3 could have been skipped.
Updated all 150 batteries to 1.4
Completed IMU calibration.
Completed camera calibration.
Completed stick calibration.
Completed compass calibration outside.
Now just gotta complete battery calibration.
Thanks gentlemen.
Last edited:
- Joined
- Mar 29, 2015
- Messages
- 1,257
- Reaction score
- 590
- Location
- Buckie, Scotland, UK
- Website
- www.moraysky.co.uk
How many batteries? You only need to calibrate the batteries if you did not previously install 1.3.0.0 and recalibrate then.
I think most of the problems are people not reading and following instructions. I'm about as tech savvy as my 8 year old Grandson but I can read and follow DJI's instructions. If you start reading from the beginning if you have a new Bird it will help you in knowing and understanding it. Not criticizing anyone!!
From DJI Developer sites, the I1 platform is much larger than the Phantom 3; thus the algorithm currently used will not satisfy the larger sUAS platforms. Short version.
- Joined
- Mar 29, 2015
- Messages
- 19
- Reaction score
- 6
- Age
- 66
- Location
- Nashville, TN
- Website
- www.johnalbaniphotos.com
Hi John,
I've always calibrated the IMU after a firmware update, I make it part of my update routine. I recalibrate everything.
- Joined
- Mar 29, 2015
- Messages
- 19
- Reaction score
- 6
- Age
- 66
- Location
- Nashville, TN
- Website
- www.johnalbaniphotos.com
Thanks. Good to know!!Hi John,
I've always calibrated the IMU after a firmware update, I make it part of my update routine. I recalibrate everything.
150? Wouldn't a nuclear powercell suffice lol, too funny.. That's allot of batteries..
I got the same exact behavior. Long beep, but firmware seems to have been upgraded.
And it will do the long beep again if I leave the .bin file on the memory card.
- Joined
- Mar 17, 2015
- Messages
- 1,378
- Reaction score
- 852
- Location
- Right Above You
- Website
- www.hoveranalytics.com
Flew my Xenomorph this morning with all 7 batteries.
Rock'n Roll solid!
No glitches, no anomaly to the AC.
I did have a "disconnect" event but came back on after 5 seconds and I still had full control of the AC.
Flew it father than I had anticipated and video was just outstanding.
Only other drama was not the AC's fault or mine but the pucker factor is when I let the waypoint took over the craft to its first location. which was 10' away from me and when I completed the route it was 20 feet away.
Once it engaged it swung back rapidly towards me and a fear came down on me that it would hit the trees behind me. Fortunately it stop where it supposed to on waypoint 1. After that it was all smiles.
Good Job. DJI
Rock'n Roll solid!
No glitches, no anomaly to the AC.
I did have a "disconnect" event but came back on after 5 seconds and I still had full control of the AC.
Flew it father than I had anticipated and video was just outstanding.
Only other drama was not the AC's fault or mine but the pucker factor is when I let the waypoint took over the craft to its first location. which was 10' away from me and when I completed the route it was 20 feet away.
Once it engaged it swung back rapidly towards me and a fear came down on me that it would hit the trees behind me. Fortunately it stop where it supposed to on waypoint 1. After that it was all smiles.
Good Job. DJI
Last edited:
Similar threads
